Entry Titles Only           Project PDF with: Title Only Title & Description All All w/ Picture Title - Last Entry First First Entry First Create PDF

Entry #	Created	Title	Category	Hours	# Pictures

262	Jan 28, 2021	Nose Gear	Fuselage		3
Test nose gear actuator, nose gear door hinges and cover for nose

 

261	Jan 27, 2021	actuator	Fuselage		2
Remake the actuator connection bracket

 

260	Jan 26, 2021	Actuator	Fuselage		3
Continue fitting and connecting actuator to main gear cables

 

259	Jan 25, 2021	Actuator	Fuselage		4
Connect actuator to main gear cables, build up nose gear door hinges

 

258	Jan 24, 2021	Actuator	Fuselage		5
Fitting actuator

 

257	Jan 19, 2021	Main gear opening, micro on canard	Fuselage		9

 

256	Jan 15, 2021	Misc items	Fuselage		9
Fresh air vent installation, flanges for main gear openings at fuselage, glass actuator brackets and micro wing tips on canard

 

255	Jan 15, 2021	Close main gear opening, storage	Fuselage		5
Continue to glass main gear opening, create hinge for storage in door and glass actuator support bracket

 

254	Jan 12, 2021	Closing main gear opening, fabricate strake door	Fuselage		4
Closing main gear opening, fabricate the door to the storage area in the strake on the door

 

253	Jan 08, 2021	Close off main gear at fuselage	Fuselage		4

 

252	Jan 06, 2021	Canard and Cowlijng Glass work	Fuselage		8

 

251	Dec 18, 2020	Sanding & Actuators	Fuselage	7	5
Built doors and latches for storage compartment in doors; fabricated support flanges in keel access panel and continued to fabricate actuator support structure in keel

 

250	Dec 17, 2020	Canard Wing Tips, Actuator	Canard	7	6
Glassed other side of wing tips on the canard where I made the cut to reset them; glued and glassed in place the base plate to attach the actuator supports; micro the areas around the hinges and door compartment

 

249	Dec 17, 2020	Canard Wing Tips, Actuator	Canard	7	6
Glassed other side of wing tips on the canard where I made the cut to reset them; glued and glassed in place the base plate to attach the actuator supports; micro the areas around the hinges and door compartment

 

248	Dec 16, 2020	Glassed Spots on Canard	Canard	7	7
Cut wing tips and reset them so the trailing edge fit when elevator is in neutral position; filled holes around hinges in canard

 

247	Dec 15, 2020	Reset Elevator Hinges	Canard	8	4
Reset the hinges in the canard for the elevators and positioned the nose gear actuator

 

246	Dec 13, 2020	Actuators, Doors	Fuselage	6	5
Cut opening in the keel to hold the brace for the two actuators; prepared the storage space in the doors and attached the struts to the doors

 

245	Dec 12, 2020	Reset Elevator	Canard	7	3
Removed hinges from the canard and prepared to reset them; fabricated support for actuators; prepared hardware to attach door struts

 

244	Dec 11, 2020	Nose Gear Actuator and Landing Light	Nose Gear	7	2
Continued to fabricate the nose gear retract system and worked on the co-pilot side landing light

 

243	Dec 10, 2020	Nose Gear Actuator and Landing Light	Nose Gear	7	2
Began to pull together parts for the nose gear actuator; cut the leading edge of the wing for co-pilot side landing light

 

242	Dec 09, 2020	Retract System & Landing Lights	Main Gear	7	5
Prepared to install Linak actuators for landing gears, prepared to cut out wing hole for landing lights

 

241	Dec 07, 2020	Canard Glass work and Actuator Installation	Fuselage		3

 

240	Dec 06, 2020	Canard & Elevators	Canard	5	5
Sanded and filled elevator ends, canard wing tips and winglets

 

239	Dec 05, 2020	Canard & Wings	Canard	6	8
Glassed and micro filled elevator ends, canard wing tips and winglets at rudder

 

238	Dec 02, 2020	Door Gas Struts	Canard	7	3
Moved plane to new hangar; replaced hard point for door struts

 

237	Nov 20, 2020	Sanding and micro work	Fuselage	7	5
Micro work and sanding doghouse, wings and cowling

 

236	Nov 19, 2020	Sanding and micro work	Fuselage	6	7
Sanding and micro work on wings and cowling, repair doors

 

235	Nov 18, 2020	Cowling fit and micro	Fuselage	7	5
More work fitting the back of the cowling. as well as sanding area where cowling meets the wing; more filling and sanding the wing/strake area and doghouse as well.

 

234	Nov 17, 2020	Completed glassing cowling	Fuselage	7	8
Continued work on cowling building up the edges where the cowling meets the wing; more sanding and micro on doghouse and elevators

 

233	Nov 16, 2020	Fit cowling	Fuselage	6	3
Used aluminum tape to build edge with micro where cowling meets the wing; began to repair where the upper winglet on co-pilot side was damaged years ago when shipping

 

232	Nov 15, 2020	Fit cowling	Fuselage	8	6
Glassed the inside of the cowling to create a flange; more sanding and micro filling doghouse and wing/strake area

 

231	Nov 14, 2020	Cowling fit and micro	Fuselage	7	10
More sanding and micro filling of doghouse and the seam connecting the wing to the strake using plastic (Mike, the painter's idea)

 

230	Nov 13, 2020	Cowling fit to wing	Fuselage	8	9
Began the process of fitting the cowlings to the wing.

 

229	Nov 12, 2020	Sanding and micro work	Fuselage	7	9
Lots of sanding and micro filling again! Cut the molds for the landing light lenses

 

228	Nov 11, 2020	Landing Light	Fuselage	7	3
Various sanding and micro work and cut the mold for the pilot side wing landing light

 

227	Nov 10, 2020	Micro work	Fuselage	8	6
Filled spots with micro around the doors and on the canard; did a layup one the leading edge of the wing to create a mold for the landing light lens

 

226	Nov 09, 2020	Doghouse, Nose Gear Boot	Canard	7	7
Continued working on fitting the doghouse to the canard; placed the rubber boots in the keel to provide insulation to the cabin from the nose gear

 

225	Nov 08, 2020	Doghouse	Canard	7	3
Continued work on fitting the doghouse to the canard and fuselage; filled the back of the doghouse to refit it to the canard

 

224	Nov 07, 2020	Doghouse	Canard	8	3
Continued to glass the base of the doghouse to the canard; did more sanding and micro filling

 

223	Nov 06, 2020	Sanding and micro work	Fuselage	7	4
Micro work on fuselage and canard; fitting doghouse is not easy!

 

222	Nov 05, 2020	Sanding and micro work	Canard	7	2
Micro work on door and add doghouse

 

221	Oct 27, 2020	Micro work	Fuselage	6	3

 

220	Oct 26, 2020	Fabricate door/strake pocket spaces and other glass and micro work	Fuselage		5

 

219	Oct 23, 2020	Door strake	Fuselage		6
Fabricate door/strake pocket spaces and other glass and micro work

 

218	Oct 22, 2020	Fabricate door/strake pocket spaces and other glass and micro work	Fuselage		7

 

217	Oct 21, 2020	Fabricate door/strake pocket spaces and back to doghouse	Fuselage		5

 

216	Oct 20, 2020	Install baffles in strake/wing space and leading edge of strake on doors	Fuselage		5

 

215	Oct 19, 2020	Install baffles in strake/wing space and leading edge of strake on doors	Fuselage		4

 

214	Oct 15, 2020	Install baffles in strake/wing space and at main gear well	Fuselage		5

 

213	Oct 14, 2020	Install side controls	Controls		4

 

212	Oct 13, 2020	Install side controls	Controls		4

 

211	Oct 12, 2020	Install side controls	Controls		3

 

210	Oct 10, 2020	Glass work on canard	Canard		2

 

209	Oct 09, 2020	Glass work on canard	Canard		3

 

208	Oct 08, 2020	Re-center Canard on Fuselage	Canard		8

 

207	Oct 07, 2020	Re-center Canard on Fuselage	Canard		5

 

206	Oct 06, 2020	Re-center Canard on Fuselage	Canard		5

 

205	Oct 05, 2020	Re-center Canard on Fuselage	Canard		2

 

204	Oct 04, 2020	Sanding and body work	Fuselage		6

 

203	Oct 03, 2020	Sanding and body work	Fuselage		4

 

202	Oct 02, 2020	Sanding and body work	Fuselage		5

 

201	Sep 30, 2020	More sanding and painting components for main gear and nav light	Fuselage	7	6

 

200	Sep 29, 2020	More sanding and painting components for main gear and nav light	Fuselage	7	6

 

199	Sep 28, 2020	Wheel well paint and form and sand end of winglet for nav light	Fuselage	8	5

 

198	Sep 27, 2020	Prime and sand	Paint / Decals	6	5

 

197	Sep 26, 2020	Glass nav light support and caps in wings	Fuselage	7	3

 

196	Sep 25, 2020	Design and build nav light support and prime main gear well	Fuselage	8	5

 

195	Sep 15, 2020	Sand and micro	Fuselage	7	0

 

194	Sep 14, 2020	Repair wing surface and	Fuselage	8	7

 

193	Sep 12, 2020	Prime and paint component parts	Paint / Decals	6	3

 

192	Sep 11, 2020	Work on component caps and doors	Fuselage	7	5

 

191	Sep 10, 2020	Prep and paint components	Paint / Decals	8	4

 

190	Sep 09, 2020	Fuselage body work	Fuselage	7	3

 

189	Sep 08, 2020	Sand and prep components	Paint / Decals	7	4

 

188	Sep 07, 2020	Prime and paint components	Paint / Decals	7	2

 

187	Sep 05, 2020	Wheel Well & Other Paint	Wings	2	0
Prepared to continue to paint the wheel wells, inside gear doors, and inside wing bolt covers, as well as other its in the nose.

 

186	Sep 04, 2020	Primed Bottom of Plane	Wings	6	12
Primed the bottom of the wings and fuselage, as well as many accessories. Began prep to paint the inside of the wheel wells and other accessories, including the wing bolt covers.

 

185	Sep 03, 2020	Prep for Prime	Wings	5	6
Did more sanding and prepared for the paining of primer on the bottom of the wings and fuselage for Friday.

 

184	Sep 02, 2020	Prep for Prime	Wings	6	2
Cleaned and glassed the inside of the winglets where the rudder cables will meet the rudders. Also continued to fill holes with micro and did more sanding.

 

183	Sep 01, 2020	Prep for Prime	Wings	6	2
Continued sanding and filling holes and uneven spots, especially around the wings where the bottom cowling meets the wing.

 

182	Aug 31, 2020	Prep for Prime	Wings	6	6
Strengthened the edges of the cowling with an additional layer of BID over the micro. Sanded and filled the mains with micro. Spend time doing a 3 BID layup around the windshield to support the upholstery. I should have done 5 or 6 sheets of BID instead of 3. May add more layers next week.

 

181	Aug 30, 2020	Cowling	Fuselage	1	2
Spent one hour sanding the edges of the bottom cowling and applying another layer of micro.

 

180	Aug 29, 2020	Cowling	Fuselage	4	5
Attached bottom cowling with clecos and applied the first layer of micro where the cowling meets the wing.

 

179	Aug 28, 2020	Cowling	Fuselage	6	4
Cut and sanded the flanges. Sanded the top cowling and applied micro to spots on the wings. Continued sanding.

 

178	Aug 27, 2020	Cowling	Fuselage	7	4
Formed the flange to both wings where the lower cowling will be attached to the wing. Applied one layer of carbon fiber BID with one layer of regular BID to the inside edges of the top cowling to reinforce the edges where I took off too much material when I cut the cowling to fit the wings.

 

177	Aug 26, 2020	Sanding	Fuselage	7	5
Sanded bottom of wings, as well as the bottom of the fuselage with 180 grit. Cut cowling in two and applied a stip of carbon fiber BID with one layer of regular BID to the inside edges of the bottom cowling to reinforce the edges.

 

176	Aug 25, 2020	Cowling	Fuselage	6	6
Applied two BID layup to the insides of the cowling connecting the top and bottom together. Sanded bottom of wing again where kingbolt covers are placed. Applied another coat of micro.

 

175	Aug 24, 2020	Cowling	Fuselage	7	5
Applied two BID layups to cowling sides along length of the cowlings. Applied micro to bottom of wings at the points of the wing bolt covers. Cleaned and covered bottom windows and applied micro to the edges of the windows.

 

174	Aug 22, 2020	Cowling	Fuselage	7	5
Cut and fit the bottom and top cowling to the fuselage and secured with clecos. Applied several layups of BID between cowling and wing as first step in forming the seam between the two.

 

173	Aug 21, 2020	Sanding	Main Gear	6	0
Sanded second gear leg. Applied more micro to the bottom of the strakes and wings to create a smooth transition and fit.

 

172	Aug 20, 2020	Sanding	Main Gear	4	0
Applied micro to second gear leg. Sanded and cleaned lower strake windows.

 

171	Aug 19, 2020	Wing Bolt Covers	Wings	6	3
Sanded one gear leg. Applied micro to the edges of the lower strake (shelf) windows. Sanded the bottom of wing and strakes again while fitting the wing bolt covers.

 

170	Aug 18, 2020	Sanding	Wings	5	1
Applied micro to one of the gear legs in prep of painting. Sanded bottom of wings and applied another skim of micro. Fabricated flanges for the three remaining covers for the wing bolts.

 

169	Aug 17, 2020	Sanding	Wings	6	0
Sanded wings and applied coat of micro to the joints between the strakes and wings, as well as filled areas near the winglets.

 

168	Jul 31, 2020	Wing Bolt Covers	Wings	4	0
Glassed over the two attachment points for the wing bolt covers. Sanded the one wing bolt cover that has the flange.

 

167	Jul 30, 2020	Wing Bolt Covers	Wings	6	9
Fit the two bottom wing bolt covers to the openings and glued the attach stops to the wing with Cabo. Sanded flanged cover and added two BID plus to the bottom flange side of the cover.

 

166	Jul 29, 2020	Sanding	Wings	4	3
Reattached both wings and noticed how well the strakes met the wings on the bottom. Will require very little micro fill. Sanded bottom of fuselage. Began to create a flange for one of the covers to see if they would work.

 

165	Jul 28, 2020	Gear doors	Main Gear	4	0
Trimmed the gear doors at the top far enough to enable the gears to be lowered fully without having the doors hit the fuselage.

 

164	Jul 27, 2020	Gear doors	Main Gear	4	0
Spent the day fitting the gear doors to the openings now that the booties are on.

 

163	Jul 24, 2020	Wing Bolt Covers	Wings	4	5
Cut three more wing bolt covers and the aluminum attachment strips. Riveted screw locks to each attachment strips.

 

162	Jul 23, 2020	Booties	Main Gear	8	4
Cut gear legs off at the bottom to accommodate the new aluminum booties. Leveled wheels with the booties on. Fit both booties and used structural cement to permanently attach booties to legs.

 

161	Jul 22, 2020	Drain pipe	Fuel System	4	0
Decided not to combine the water drain to the fuel drain in case the water ever froze in the drain line. Drilled a separate water drain hole for the separate aluminum line.

 

160	Jul 21, 2020	Vent lines	Fuel System	4	5
Completed vent line connections. Fit center ceiling overhead fresh air duct and clecoed it in. Fit a drain tube from the fresh air duct where water can enter to connect to the fuel vent line that extends through the bottom of the fuselage. Sanded new opening for fuel drain.

 

159	Jul 20, 2020	Sanding	Fuselage	8	3
Cleaned layups from Saturday. Tapped sump tank fuel line connectors and re-installed. Now the gear can move fully without interference. Replaced paper and tape covering over bottom windows. Cleaned windows and recovered. Cut out and replaced PVC pipe used to cover drain valve because the angle changed when bolting in the sump tank after sanding more of the area around the tank to provide more clearance for the gear.

 

158	Jul 18, 2020	Sump Tank	Fuel System	7	0
Tried to fit sump tank but fuel line connectors still are in the way of full gear movement. Glassed the 4 areas on the ceiling where the door hinges are. Seems people are getting water leaks when it rains so now this area is completely closed.

 

157	Jul 17, 2020	Sump Tank	Fuel System	7	2
Installed PVC pipe around fuel drain on bottom of fuselage. Removed sump tank and re-installed vent and fuel connectors so that the sump tank would not interfere with the gear legs when retracting

 

156	Jul 16, 2020	Sanding	Fuselage	5	0
Did sanding and micro filling of the bottom of the fuselage, as well as other small tasks.

 

155	Jul 15, 2020	Gear doors	Main Gear	6	0
Did an initial fit of the co-pilot side gear door More micro filling and sanding.

 

154	Jul 14, 2020	Gear doors	Main Gear	5	0
Cleaned the glass work from the previous day. Cleaned both gear doors. Did second layup on the co-pilot side wheel well. Fit the pilot side gear door. Filled in spots with micro.

 

153	Jul 13, 2020	Gear doors	Main Gear	7	5
Did second layup on the pilot side of the wheel well. Sanded bottom of fuselage (100 grit). Glassed 2 BID on each gear door because I didn’t do a layup over the entire gear door as I should have previously.

 

152	Jul 02, 2020	Gear doors	Main Gear	6	3
Fit the co-pilot side main gear door. Glassed reinforcing layups on the door. Corrected pilot side gear door opening at strake by adding glass layup. Sanded and cleaned small door cover to potentially use to cover wing bolt access hole. Sanded inside of cabin.

 

151	Jul 01, 2020	Gear doors	Main Gear	6	3
Fabricated and glassed support for main gear doors on each gear leg. Fabricated potential door cover for access hole to wing bolts.

 

150	Jun 30, 2020	Gear doors	Main Gear	7	0
Glassed the inside of the fuselage in the morning, including both NACA scoops, fresh air scoop and both shelves (back, sides and front). Prepared to fit main gear doors on legs. Shaped the foam for reinforcing gear doors.

 

149	Jun 29, 2020	Fuel strakes	Fuel System	8	0
Sanded interior of cabin in preparation for glassing. Painted with Jeffco both wheel wells. Prepared the four baffles to eventually be placed between the fuel bulkhead and spar. Will install following fuel leak test. Glassed the engine bulkhead where it meets the spar. Prepared all the glass and plastic templates for the layups in the morning.

 

148	Jun 27, 2020	Micro and sanding	Fuselage	6	6
Micro filled the leading edges of the strakes on both sides, as well as created a bead and filled the space where the strake meets the fuselage on both sides. Sanded and prepared all the glass work that needs to be done on the inside of the cabin on Monday.

 

147	Jun 26, 2020	Fuel strakes	Fuel System	6	3
Worked on the inside of the wheel wells - cut triangular space (top glass and foam only), then glassed space and around the edge of the wells on both gears.

 

146	Jun 25, 2020	Fuel strakes	Fuel System	7	7
Glassed co-pilot side connecting the spar to the fuel bulkhead (succeeded on first try!). Glassed Triax on bottom of the ends of the inside ends of the strakes. Glassed the leading edge of the strakes.

 

145	Jun 24, 2020	Fuel strakes	Fuel System	8	4
Sanded previous day layups. Sanded and prepared area between fuel bulkheads and spar. Glassed pilot side only. Prepared and glassed ends and inside ends of strakes.

 

144	Jun 23, 2020	Fuel strakes	Fuel System	7	5
Sanded and cleaned previous day’s work. Glassed the other side of the back of the wings at the strake line and the back of the strakes where it meets the wings. Glassed the exhaust area where the oil cooler air leaves the nose.

 

143	Jun 22, 2020	Fuel strakes	Fuel System	6	7
Cut the micro where the wings meet the strakes. Removed the wings and turned the plane upside down. Glassed one side of the back of the wings at the strake line.

 

142	Jun 20, 2020	Fuel strakes	Fuel System	3	4
Sanded and added micro to upper wing and at where wing meets the fuselage.

 

141	Jun 19, 2020	Fuel strakes	Fuel System	5	7
Cut tip of co-pilot side strake to fit on door. Glassed co-pilot side top strake at fuselage. Sanded both wings at strake and applied micro to begin to even top of strakes to top of wings.

 

140	Jun 18, 2020	Fuel strakes	Fuel System	8	11
Painted and installed co-pilot side top strake. Cut tip of pilot side strake to install on the door. Glassed top of pilot side strake. Applied Veloxipoxy with Cabo and flox to joint between wing and strake on pilot side. Cleaned and sanded bottoms of both rudders.

 

139	Jun 17, 2020	Fuel strakes	Fuel System	7	0
Cleaned bottoms of both rudders and glassed ends over each hing arm. Painted and installed pilot side top strake.

 

138	Jun 16, 2020	Rudder installation	Controls	8	0
Cut and formed hardpoint for rudder hinge arms. Installed hinge arm and hardpoint to the bottom of both rudders with Cabo. Test fitted rear bench and decided to wait until after the vanity firewall is installed before finalizing location of bench.

 

137	Jun 15, 2020	Rudder installation	Controls	6	1
Installed spring mechanism and latch in both winglets and rudders. Added one more layup of BID to the insides of the fresh air vents.

 

136	Jun 13, 2020	NACA Air Vents	Fuselage	2	0
Glassed co-pilot side vent.

 

135	Jun 12, 2020	Vent lines	Fuel System	7	0
Glassed pilot side vent. Glued co-pilot side vent. Installed all fuel vent lines in cabin.

 

134	Jun 11, 2020	NACA Air Vents	Fuselage	7	2
Fit and glued the co-pilot side NACA scoop to the fuselage. Removed pilot side scoop from mold and fit to pilot side vent. Cut and glued 1-1/2” aluminum pipe to NACA scoop. Fit cover for rudder hing and tapped four screws to hold the cover. Riveted, glued and glassed flange to the cover to hold the warm air cable. Began installing vent lines inside the cabin.

 

133	Jun 10, 2020	NACA Air Vents	Fuselage	5	1
Continued to spray paint nose compartment. Cut NACA opening on both sides of the fuselage to provide fresh air to the cabin. Glued the 1-1/2” aluminum pipe to the NACA scoop.

 

132	Jun 09, 2020	Nose section	Fuselage	6	10
Painted trunk spray paint to nose compartment. Ran out of spray paint. Fabricated a small flange in glass to hold the cabin heat pull-to-open handle.

 

131	Jun 08, 2020	Nose section	Fuselage	6	0
Painted primer on interior of nose section of the plane. Performed other clean up activities.

 

130	Jun 07, 2020	Gear doors	Nose Gear	2	0
Removed pilot side nose gear door, cut and sanded excess glass off and micro filled both sides. Added additional micro to the co-pilot side gear door.

 

129	Jun 06, 2020	Gear doors	Nose Gear	4	0
Removed co-pilot side nose gear door, cut and sanded excess glass off and micro filled both sides. Set pilot side nose gear door in place with 2 layers of BID to widen the door. Made a small flange in glass to hold the cabin heat pull-to-open handle.

 

128	Jun 05, 2020	Gear doors	Nose Gear	6	3
Identified location of nose gear door closing mechanism but realized that I trimmed the nose gear doors to narrow. Cut 2 layers of BID for both doors and glassed the co-pilot side door and set it in place to dry.

 

127	Jun 02, 2020	Oil cooler	Fuel System	6	5
Cleaned previous days glass work on the bench (bottom and back). Glassed the two sight gauges. Cut and wrapped two 13’ tubes for oil cooler.

 

126	Jun 01, 2020	Fuel strakes	Fuel System	4	4
Glued the cover of the sight gauges to the backs in the shelf area of the cabin. Glassed the bottom of the bench (support to base of bench) and re-glassed the hinge bar to the larger back of the bench.

 

125	May 29, 2020	Fuel strakes	Fuel System	6	4
Applied two layers of Triax to each side of the end of the strake (outside the fuel cells) to strengthen the ends. Fit the vertical support for the bench in the cabin. Glued (Cabo) the bench seat to the vertical support.

 

124	May 28, 2020	Fuel strakes	Fuel System	4	0
Sanded areas where I missed with the Jeffco and applied two coats. Sanded the tops of both strakes in prep for painting next week. Drilled openings in all pin holes in the sight gauges. Another sleeve came out and needed to be glued in with Cabo.

 

123	May 27, 2020	Fuel strakes	Fuel System	3	2
Painted two coats of Jeffco on the remaining two larger fuel cells on both strakes.

 

122	May 26, 2020	Fuel strakes	Fuel System	4	7
Painted the back fuel cells in both strakes. Drilled openings in the pin hole sight gauges. One sleeve came out and I had to glue it in the Cabo this time.

 

121	May 24, 2020	Fuel strakes	Fuel System	4	2
Painted two fuel strake cells with Jeffco (2 coats). Mixed too much in the first batch and within 45 minutes had an exothermic reaction. Second batch was much smaller and applied second coat easily.

 

120	May 23, 2020	Sight gauges	Fuel System	4	5
Glued white plexiglass in place and glued pin hole flange to allow fuel to enter the sight gauge. Prepared rest of strake for painting.

 

119	May 22, 2020	Fuel strakes	Fuel System	6	1
Sanded the bulkhead and measured and cut two new holes in each bulkhead to fill with Cabo and eventually fit the pin hole flange for the fuel to enter the gauges. Did more sanding.

 

118	May 21, 2020	Sight gauges	Fuel System	7	4
Cut holes in the fuel bulkhead and filled with Cabo to accommodate the brass fitting for the sight gauges. Chad mentioned he had two sight gauges for the Standard Velocity and I looked at them. While smaller they are more professionally made. I calculated that if placed at the bottom of the bulkhead the sight gauges could register between 8 gallons at the bottom to 26 gallons at the top for each wing. That’s 20% at the bottom (or 1 hr at max burn) to 75% at the top. This is sufficient for the purpose at hand.

 

117	May 20, 2020	Sight gauges	Fuel System	6	2
Sanded and cleaned the strakes. They are ready for painting. Heated and formed two sight gauges using the molds built. They came out ok but not great.

 

116	May 19, 2020	Canard flanges	Canard	7	11
Cleaned the canard flanges and sanded the shelf windows. Will need a small amount of micro to make the boarders for the windows look good. Prepared more molds to see if I can form the sight gauges by applying heat only to the plexiglass and squeezing the plexiglass to the shape of the mold.

 

115	May 18, 2020	Canard flanges	Canard	6	1
Received the adjustable jacks for the airplane. Assembled one and realized they stood too tall. Instead of returning and getting a new set, I hired Tyrone in the machine shop here in Sebastian to cut 15 inches off of the legs. Removed the canard, sanded and cleaned the canard flanges and filled the holes with Cabo. Prepared a male mold and tried to heat a small piece of plexiglass to see if I can form the sight gauges.

 

114	May 01, 2020	Flange	Canard	6	7
Cleaned the sump tank and temporarily installed it in the fuselage. Drilled bolt holes and hole in the bottom of the fuselage to enable draining. Glassed the front flanges for the canard with 6 layers of Triax.

 

113	Apr 30, 2020	Flange	Canard	6	4
Glassed the sides of the fuel sump tank. Prepared and installed the canard cabin side flanges with 6 layers of Triax.

 

112	Apr 29, 2020	Engine Firewall	Firewall	7	9
Cut and install engine firewall insulation and metal cover. Cut and glassed the fuel filler caps into the two upper strakes. We were shown that the sump tank need to be modified (cut) to accommodate the Continental engine mounts. The two sides were cut and new sides were formed and glued in with Jeffcoc paint.

 

111	Apr 28, 2020	Fuel Strakes	Fuel System	5	0
Cleaned the hard points from the glass layup of the previous day. Installed the shelf windows.

 

110	Apr 27, 2020	Fuel Strakes	Fuel System	7	1
Sanded and prepared the fuel gauge and fuel vent hard points for glassing. Glassed with 2 layers of BID. Glassed the other sides of the shelf window covers. Cut the shelf windows and covered them to protect them and prepared them to be installed.

 

109	Apr 25, 2020	Fuel Strakes	Fuel System	6	3
Cut holes for fuel vents on both sides. Prepared hard points for both fuel gauges and fuel vents and glued them in place. Cut shelf window cover forms in foam and glassed one side. Will use them to cover the shelf windows when I want to use the shelf for storage.

 

108	Apr 24, 2020	Fuel Strakes	Fuel System	6	2
Cleaned the two front shelf bulkheads and sanded areas inside fuselage to install the fuel gauge and fuel vents on both sides. Measures and cut holes for both. Sanded and cleaned shelf window areas in prep to install 1/8” windows.

 

107	Apr 23, 2020	Fuel Strakes	Fuel System	7	1
Sanded and prepped the front shelf bulkhead for glassing and also the two fuel strainer faces inside the fuselage. Cut four sheets of UNI for each shelf bulkhead back side (internal side) and prepared them on a sheet of plastic. Installed both on the backs of each bulkhead and spent a lot of time getting the bubbles out! Placed two layers of BID over the fuel strainer hard point. Spent time cleaning the interior of the pilot door.

 

106	Apr 22, 2020	Fuel Strakes	Fuel System	6	5
Routed out foam from the ends of all the fuel bulkheads and baffles. Sanded and cleaned fuel area again. Cut and formed foam core with heat gun to fit and become the forward bulkhead at the door. Glassed one side with BID.

 

105	Apr 21, 2020	Fuel Strakes	Fuel System	5	4
Rough sanded all compartments in both strakes for excess glass and prep for painting. Put 2 layers of BID over bottom ends of flanges installed to hold strakes at back ends of the strake at the fuselage. Glassed also back edge of aft fuel bulkheads behind gear from inside the fuselage. Cut hole and installed fuel strainer threaded hard point.

 

104	Apr 18, 2020	Fuel Strakes	Fuel System	5	8
Designed and fabricated a pattern for the strake windows out of plywood. Using the pattern we cut and removed the glass and foam from the lower stakes in prep for installation of the plexiglass (to be installed at a later date).

 

103	Apr 17, 2020	Fuel Strakes	Fuel System	5	4
Cleaned and sanded the strake baffles, and installed the flanges on the top, back of the strakes. Began design of strake windows. Installed and checked installation of front seats.

 

102	Apr 16, 2020	Fuel Strakes	Fuel System	8	4
Assembled front seats. Glassed all the sides of the baffles on the co-pilot strake.

 

101	Apr 15, 2020	Fuel Strakes	Fuel System	8	7
Fabricated a 5-layer BID lay up on a right angle steel beam to make a flange for the top strake along the fuselage and spar on each side of the plane. Continued glassing the fuel bulkheads. Set in the 3 fuel baffles on each tank. Glassed the bolts and washers to the seats so they would be permanent attached to the seat base.

 

100	Apr 14, 2020	Seats	Fuselage	6	5
Fit the front two seats on their respective frames. Cut the bold holes, cleaned out area around where bolts will be placed and put Cabo on the holes to creat a hard point. Glassed a few more corners in the strakes.

 

99	Apr 13, 2020	Fuel Strakes	Fuel System	5	0
Glassed the remaining bottoms of the strake bulkheads and started on the vertical sections of the fuel bulkheads.

 

98	Apr 11, 2020	Fuel Strakes	Fuel System	5	0
Glassed more of the bottoms of the fuel bulkheads.

 

97	Apr 10, 2020	Fuel Strakes	Fuel System	7	0
Glassed the bottoms of 3 of the longest (and hardest to do) bulkheads on the co-pilot side today, as well as more on the pilot side.

 

96	Apr 09, 2020	Fuel Strakes	Fuel System	7	0
Sanded all sealed contact areas at the base of the fuel bulkheads. Glassed the bottoms of 3 of the longest (and hardest to do) bulkheads on the pilot side.

 

95	Apr 08, 2020	Fuel Strakes	Fuel System	7	4
Filled the slots on the bottoms (and sides) of all the fuel bulkheads with Cabo and glued them in place on both lower strakes of the plane.

 

94	Apr 07, 2020	Fuel Strakes	Fuel System	8	2
Trimmed and fit the tops of all the baffles and fuel bulkheads on the co-pilot side and hot glued them in place. Cut mouse holes in all the baffles. Sanded all forms and cleaned

 

93	Apr 06, 2020	Fuel Strakes	Fuel System	6	0
Trimmed and fit the tops of all the baffles and fuel bulkheads on the pilot side and hot glued them in place.

 

92	Apr 04, 2020	Fuel Strakes	Fuel System	4	2
Continued cutting and forming the baffles for the fuel tanks. Now all baffles are fit together but for the fit to the top strake. Will cut all the pieces to fit the top strake over the next few days.

 

91	Apr 03, 2020	Fuel Strakes	Fuel System	7	4
I went to the airport and worked solo on my bird. I wear a mask at the airport (due to the dust) and outside (to adhere to standards we all should follow due to Covid-19). Then I continued cutting and forming the baffles for the two fuel tanks.

 

90	Apr 02, 2020	Fuel Strakes	Fuel System	8	0
I cut and formed some of the bulkheads and baffles for the two fuel tanks. Will take a while to get these right before I glass them in.

 

89	Apr 01, 2020	Fuel Strakes	Fuel System	8	6
Glassed the two wheel wells to the lower strakes on the inside of the wells. Built the other side of the composite sheet to be used for the fuel baffles and bulkheads. Florida's governor issued a stay-at-home order effective Thursday at midnight. Will see how this affects my build.

 

88	Mar 31, 2020	Fuel Strakes	Fuel System	7	3
Glassed the two wheel wells to the lower strakes on outside only. Built one side of the composite sheet to be used for the fuel baffles and bulkheads. Will do the reverse side tomorrow.

 

87	Mar 28, 2020	Fuel Strakes	Fuel System	2	0
Sanded and prepared the wheel wells to be glassed on Tuesday.

 

86	Mar 27, 2020	Fuel Strakes	Fuel System	8	4
Glassed the outsiders of the pilot gear leg housing and the seam of the pilot side wheel well. Worked on the doors by replacing the knobs and repairing the closing mechanism.

 

85	Mar 26, 2020	Fuel Strakes	Fuel System	7	2
Glassed the outsiders of the co-pilot gear leg housing and the seam of the co-pilot side wheel well. Fit the pilot side wheel well and created the fairing for the well.

 

84	Mar 25, 2020	Fuel Strakes	Fuel System	7	1
Cleaned the glass work from the previous day and the fit the co-pilot side wheel well and glassed the fairing.

 

83	Mar 24, 2020	Fuel Strakes	Fuel System	8	4
Glassed the insides of the gear door housing. Glassed the opening where the strakes meet the fuselage.

 

82	Mar 23, 2020	Fuel Strakes	Fuel System	6	1
Began fitting the housings in the strakes for the gears. Worked on the openings for the gears to ensure there is space in the wheel well.

 

81	Mar 21, 2020	Fuel Strakes	Fuel System	6	1
Sanded upper strake on pilot side and set aside. Cut gear openings on both lower stakes to accept gear and wheels. Sanded and rounded the area where the fuselage meets the lower strakes in prep for layup.

 

80	Mar 20, 2020	Fuel Strakes	Fuel System	7	4
Removed pilot side wing and prepared upper strake on pilot side for glassing. Removed both doors and I need to replace the door latches as they are weak and will break. Cut openings in fuselage on both sides above bottom strakes.

 

79	Mar 19, 2020	Fuel Strakes	Fuel System	8	4
Used laser lever and re-plumbed the plane in both dimensions. Adjusted pilot side lower strake slightly. Bonded it and glassed it. Removed co-pilot side wing. Cut co-pilot side main gear opening in lower strake. Fit co-pilot side upper strake, sanded and did end layup to prepare to fit. Cut access hole in lower strake on co-pilot side.

 

78	Mar 18, 2020	Fuel Strakes	Fuel System	8	7
Fit both strakes and glued to spar. Glassed both on inside too to spar and glassed bottom side of co-pilot strake to fuselage. Was concerned the fitting on the pilot side was off so will re-measure on Thursday.

 

77	Mar 17, 2020	Fuel Strakes	Fuel System	6	6
Installed both wings to spar. Prepared both lower strakes to install (sanded and glassed ends where they fit on spar). Sanded both sides of fuselage to prepare to install stakes.

 

76	Mar 16, 2020	Fitting Gear Legs	Main Gear	5	3
Opened bolt holes at bushing for main gears inside the cabin at the gear bulkhead and on the exterior of the engine bulkhead. Re-installed the gears and leveled the fuselage. Cut openings in fuselage on both sides for gear to retract fully.

 

75	Mar 10, 2020	Doghouse	Canard	8	4
Cleaned glass work on canard doghouse, moved airplane and all parts to other side of the hangar in preparation to put the wings on the fuselage, then did Triax layups to main landing gear bushings on inside landing gear bulkhead and outside engine firewall.

 

74	Feb 29, 2020	Hangar Rental	Workshop		0

 

73	Feb 28, 2020	Fit Doghouse	Canard	8	2
Cut the “doghouse” to fit on the canard. Cut holes for torsion bar. Temporarily glued doghouse to the canard and did the layups to attach the doghouse to the canard (6 Triax and 2 BID to each side).

 

72	Feb 27, 2020	Installed Gears	Main Gear	7	2
Spent the day preparing and installing (gluing bushings) the main gears.

 

71	Feb 26, 2020	Installed Flanges	Instrument Panel	4	1
Installed the layup for the panel flanges.

 

70	Feb 25, 2020	Installed Brake Line Straws to Legs	Main Gear	7	4
Prepared main gear legs for attachment of straws to hold the brake line. Sanded, glued and glassed the straws to both legs. Began to install the flanges to hold the instrument panel and received side sticks to install after panel is leveled.

 

69	Feb 24, 2020	Main Gear Installation	Main Gear	4	0
Installed two 4-ply BID layup between the engine bulkhead and the gear bulkhead (under the foam cover between the bulkheads) as part of the torsion box reinforcement. Cleaned the seat frames.

 

68	Feb 23, 2020	Spar	Fuselage	4	0
Did 6–layer layup of Triax on each side of the cabin at the spar as part of the torsion box reinforcement. Removed the molded main gear sleeves from each gear and removed the aluminum foil from the gear legs.

 

67	Feb 22, 2020	Spar	Fuselage	3	1
Sanded interior by the spar, glued the foam parts between the engine and gear bulkheads to make up the torsion box. Filled and did glass layups on the aft side of the engine bulkhead where the spar meets the bulkhead (each side).

 

66	Feb 21, 2020	Sleeve to Support Gear in Fuselage	Main Gear	6	1
Cut and glassed 6 layers of Triax for each molded gear sleeve and placed them on the aluminum foil covered gear legs. Sanded and prepared the internal spar area for the next set of layups to secure the spar to the fuselage.

 

65	Feb 20, 2020	Spar	Fuselage	7	3
Prepared and installed the spar and wrapped the main gears to create a molded gear sleeve to be installed in the fuselage later.

 

64	Feb 19, 2020	Wrapped Main Gear in Carbon Sleeve	Main Gear	7	0
Wrapped the second main gear and sanded and redrilled the holes in the first landing gear leg. Worked on the fuselage for an hour.

 

63	Feb 17, 2020	Wrapped Main Gear in Carbon Sleeve	Main Gear	8	2
Sanded each of the main gears and wrapped one in three layers of glass sleeves: two carbon fiber and one regular glass. Finished taping up the interior windows for micro.

 

62	Feb 14, 2020	Windows	Fuselage		2
Taped the interior windows in prep for micro slurry finishing.

 

61	Feb 13, 2020	Bench Back and Spar Leveling	Fuselage	8	0
Took apart bench back and the tube wrapped in aluminum foil stuck hard to the glass. It took me a while to get one of the backs (smaller one) free of the hinge tube. Will try to free the other back from the tube. Don't know if I can. I turned the plane around and removed the landing gear. Placed the fuselage on slides and leveled the plane (pitch and roll). Sanded the inside of the engine bulkhead and put the spar in and leveled the spar with the plumb laser level. Will glue the spar in tomorrow after I measure the tips of the spar from the nose.

 

60	Feb 12, 2020	Sump Tank, Rear Bench and Windows	Fuselage	7	0
Glassed the braces on the sump tank. Glassed the hinge tube to the back of the rear bench. Applied micro slurry to one of the door windows. I did a very bad job. Frustrated and went home.

 

59	Feb 11, 2020	Sanding Canard and Elevator	Canard	4	1
Sanded elevator hinge and applied one more small amount of micro to the canard tips. Done with the canard for now.

 

58	Feb 10, 2020	Windows	Fuselage	6	0
Glassed the edge around the sump tank. Removed more old masking tape from interior window and from each of the two doors. Re-taped the two door windows in preparation for applying micro slurry. Sanded and applied more micro to elevator hinge areas.

 

57	Feb 09, 2020	Clean Interior Windows	Fuselage	4	1
Cut edges and sanded sump tank; sanded canard tips and continued to clean masking tape from interior windows. The combination of soaking the tape in WD-40 for a day or more and then using a heat gun at low heat works great to remove old masking tape on plexiglass.

 

56	Feb 08, 2020	Sump Tank	Fuel System	6	5
Put brass plugs in sump tank (required re-tapping several of the tank openings), painted interior of tank, placed on back and put weights on the tank to secure until cured.

 

55	Feb 07, 2020	Micro and Sanding	Canard	6	2
Sanded canard wingtips and applied more micro. Purchase WD-40 and began the process of removing the masking tape on the windows that has been there for 19 years.

 

54	Feb 06, 2020	Micro and Sanding	Canard	2	5
Applied micro to canard wing tips.

 

53	Jan 31, 2020	Hangar Rent - January 2020	Workshop		0

 

52	Jan 24, 2020	Wing Area for Ailerons	Controls	2	0
Sanded aileron areas of the wings and wingtips.

 

51	Jan 23, 2020	Wing Space for Ailerons	Controls	8	2
Prepared and glassed both internal wing areas for the ailerons. Slurried wing tip repair areas.

 

50	Jan 22, 2020	Repaired Wing Space for Ailerons	Controls	7	4
Cut the fiberglass out of the internal cavity of the pilot side wing at the aileron. Cut out the foam to make room for the full motion of the aileron. Applied slurry in prep for glassing tomorrow. Sanded opposite side of the wings and filled where needed and filled the upward side of the top of the pilot side wing where it was repaired. Finally, installed tubing (Cabo) to the inside of the cabin to channel the rudder wires. I will glass them tomorrow.

 

49	Jan 21, 2020	Changed Gap in Wings for Aileron Movement	Controls	7	0
Installed two hard points to the sump tank and glassed; evaluated the degree of movement in the ailerons and realized the factory manufactured the wings with insufficient space in the inside structure where the ailerons go. I had to cut out glass and foam, then prepare the space for re-glassing. Put micro slurry on them foam. Hopefully will be able to glass the co-pilot wing tomorrow. Temperature in Sebastian is cold (40's tonight). I will cut out the pilot wing area also tomorrow.

 

48	Jan 20, 2020	Sump Tank	Fuel System	7	4
Prepared sump tank by drilling fuel and vent holes and glued sensor plate in side of sump; glassed with triax inside the engine bulkhead and on the outside of the bulkhead to prepare for the Continental IO 550 braces; prepped spar (sanded) before installing.

 

47	Jan 18, 2020	Wingtip Repairs	Wings	4	2
Micro slurry wing tips and canard.

 

46	Jan 17, 2020	Gear Door Plates	Main Gear	6	4
Installed pulleys. Fabricated two aluminum main gear doorplates; sanded canard and both wings.

 

45	Jan 16, 2020	Main Gear Pulley	Main Gear	6	2
Fabricated main gear retract pulley system and fit in plane; glued “L” plate as part of pulley system.

 

44	Jan 15, 2020	Rudder Pedals	Controls	6	5
Completed assembly and installed ruder pedals. Beautiful evening in Sebastian.

 

43	Jan 14, 2020	Continued Repair of Wing Tips	Wings	6	1
Correctly installed the metal bracket to the canard bulkhead; continued sanding and filling wing tips with micro slurry; began assembling the rudder pedals.

 

42	Jan 13, 2020	Nose Gear Brackets	Nose Gear	8	3
Glassed the brackets; continued slurry work on the wing tips and the canard; installed metal gear bracket in the canard bulkhead (initially I rushed and it was not level so I removed it and filled the one hole), then re-installed the bracket.

 

41	Jan 12, 2020	Error in Nose Gear Door Opening	Nose Gear	4	1
Error!! I installed the “L“ brackets before ensuring and checking the gear door opening was wide enough for the nose gear. I realized I needed to open the width of the gear door 3/8” more, so I removed the glassed brackets, cleaned them and spent several hours widening the opening in the nose gear; then glued the cleaned brackets back in.

 

40	Jan 11, 2020	Nose Gear & Keel Access Hole	Nose Gear	6	2
Glassed aluminum brackets in wheel well; cut access hole wider in the keel to allow for the cover to be flush; fabricated a cover (though it may not work.

 

39	Jan 10, 2020	Nose Gear & Wing Tips	Nose Gear	6	2
Glued aluminum brackets to wheel well; sanded and continued repair of wing tips with micro slurry.

 

38	Jan 09, 2020	Nose Wheel Guides	Nose Gear	4	1
Fabricated nose gear channels and also aluminum “L” brackets to attach them

 

37	Dec 31, 2019	Hangar Rent - December 2019	Workshop		0

 

36	Dec 13, 2019	Repair Winglets	Wings	4	1
Sanded and did additional glass work to finalize damaged winglets; repaired leading edge damage

 

35	Dec 12, 2019	Repair Winglets	Wings	3	6
Filled damaged areas with cabo and glassed damaged areas

 

34	Dec 12, 2019	Prepare and Attach Ailerons to Wings	Wings	5	1
Fit completed ailerons to wings (gap will require more space to be done after the holidays)

 

33	Dec 11, 2019	Repair Winglets	Wings	3	0
Sanded and prepped both winglets to repair them from damage caused when moving the airplane kit to California

 

32	Dec 11, 2019	Prepare and Attach Ailerons to Wings	Wings	5	2
Glue hinges to ailerons

 

31	Dec 10, 2019	Prepare and Attach Ailerons to Wings	Wings	2	1
Prepare ailerons for hinges

 

30	Dec 10, 2019	Prepare and Attach Rudders to Winglets	Wings	4	3
Final set rudders to winglets (pilot side rudder hinge set needs to be fixed when i return after the holidays)

 

29	Dec 10, 2019	Prepare Canard and Elevators	Canard	2	2
Complete attaching elevator to canard and finalize glass work

 

28	Dec 09, 2019	Prepare and Attach Rudders to Winglets	Wings	3	0
Glassed remaining rudder hinges

 

27	Dec 09, 2019	Prepare Canard and Elevators	Canard	5	1
Set up and align elevators on canard, cut space for counterweights and do all glass work

 

26	Dec 08, 2019	Prepare and Attach Rudders to Winglets	Wings	6	0
Glassed hinges to rudders

 

25	Dec 07, 2019	Prepare and Attach Rudders to Winglets	Wings	8	0
Prepared and fit rudders to winglets

 

24	Dec 06, 2019	Prepare Canard and Elevators	Canard	10	1
Glue hinges in canard and prepare and attach counterweights

 

23	Dec 05, 2019	Prepare Canard and Elevators	Canard	10	3
Set hinges on elevators and cut holes in canard for hinges

 

22	Dec 04, 2019	Complete Nose Gear Installation	Nose Gear	4	5
Centered nose gear and permanently set nose gear hinge/bushing.

 

21	Dec 04, 2019	Cut Keel	Fuselage	4	1
Cut keel to adapt to RG-5

 

20	Nov 30, 2019	Hangar Rent - November 2019	Workshop		0
Hangar rental for the month of November 2019

 

19	Nov 29, 2019	Oil Cooler	Misc. Parts		0
Purchased oil cooler for installation in nose compartment

 

18	Nov 14, 2019	Keel & Sanding	Fuselage	6	2
Marked keel to cut and sanded all new glass areas before leaving for Thanksgiving

 

17	Nov 13, 2019	Landing Light Housing & Glass Gear Bulkhead	Fuselage	16	7
Installed landing light housing, sanded NACA scoops and glassed aileron support bracket and gear bulkhead

 

16	Nov 12, 2019	Seat Hardpoints & NACA Scoops	Fuselage	16	7
Installed NACA and fresh air scoops, glassed all seats and seat belt hard points

 

15	Nov 11, 2019	Oil Heater, Seat Hardpoints and NACA Scoops	Fuselage	16	8
Installed oil heater and battery tray, prepared and glassed in seat hard points (pilot & co-pilot) completed battery tray installation and cut NACA scoops

 

14	Nov 10, 2019	Oil Cooler & Battery Tray	Fuselage	6	1
Cut inlet and outlet ducts for oil cooler and prepared for battery tray, glued oil cooler ducts

 

13	Nov 09, 2019	Nose Gear Door Assembly	Nose Gear	8	2
Finalized gear door assembly and fitting

 

12	Nov 08, 2019	Nose Gear Door Assembly	Nose Gear	16	1
Cut and formed nose gear hinges, cut door and fit, glued hinges to doors

 

11	Nov 07, 2019	Set Up Shop	Workshop	4	1
Unloaded and set up parts and tools in hangar

 

10	Nov 01, 2019	Transport project from Virginia to Sebastian, FL	Research	15	2
Rented a truck and drove the project to Florida over 3 days (November 1-3, 2019).

 

9	Jul 06, 2002	Hangar Rent - June 30 through July 23, 2002	Workshop		0
Hangar rental

 

8	Jun 29, 2002	Hangar Rent - June 2002	Workshop		0
Hangar rental for June-July Head Start program (summer vacation 2002)

 

7	Jun 07, 2002	Install Nose Gear	Nose Gear	14	0
Installed nose gear assembly but not permanent

 

6	Jun 06, 2002	Position Canard & Spar	Fuselage	16	0
Set and position canard to fuselage, set and leveled center spar

 

5	Jun 05, 2002	Triax Keel to Bulkhead	Fuselage	16	0
Triax keel to bulkhead, BID keel to floor

 

4	Jun 04, 2002	Keel & Hydraulics	Fuselage	16	0
Installed hydraulics and keel hard points

 

3	Jun 03, 2002	Prepare Keel	Fuselage	6	0
Removed center keel and prepared for control system

 

2	Jul 28, 2001	Purchased Kit	Purchase Kit		0
Purchased kit at Oshkosh, 2001

 

1	Jan 12, 2001	Demo Ride	Research	1	0
First demo ride on course to purchase kit

  ------------ ------------- Totals1417    837